• 网站首页
    • 关于我们
    • 新闻资讯
    • 产品展示
    • 招贤纳士
    • 在线留言
    • 联系我们

新闻资讯

公司动态
业界资讯

当前位置:网站首页 > 新闻资讯 > 业界资讯
业界资讯

换热器结构组成

板式换热器是由一系列具有一定波纹形状的金属板片叠装而成的一种高效换热器。它凭借特有的工作原理和独特的组成结构在众多的热交换器中脱颖而出。


板式换热器由一组金属板片组成,板上有四个角孔,供冷热两种介质通过。组装时A板和B板交替排列,板片间形成网状通道,密封垫把冷热介质密封在换热器里,同时又合理的将冷热介质分开而不致混合。在通道里面冷热流体间隔流动,可以根据需要逆流或顺流,在流动过程中冷热流体通过板壁进行热交换,从而达到所需的效果。

康景辉板式换热器由一组波纹金属板组成,板上有孔,供传热的两种液体通过。金属板片安装在一个侧面有固定板和活动压紧板的框架内,并用夹紧螺栓夹紧。板片上装有密封垫片,将液体通道密封,并且引导流体交替地流至各自的通道内。金属板和活动压紧板安装在悬挂梁上,并由下导杆定位,而杆端则固定在支撑柱上,但如果其中一种液体或两种液体在换热器内不止通过一次,则接口应开在固定板和活动压紧板上。

Kangjinghui plate heat exchanger consists of a group of corrugated metal plates with holes on the plate, through which two kinds of liquid for heat transfer pass. The sheet metal is installed in a frame with a fixed plate and a movable pressing plate on the side, and is clamped with a clamping bolt. Sealing gaskets are mounted on the plates to seal the liquid passages and guide the fluids to flow alternately into their respective passages. The metal plate and the movable compaction plate are installed on the suspension beam and positioned by the lower guide rod, while the end of the rod is fixed on the support column. However, if one or two liquids pass through the heat exchanger more than once, the interface should be opened on the fixed plate and the movable compaction plate.


点击次数:  更新时间:2019-09-24 16:24:08  【打印此页】  【关闭】
上一篇:板式换热器清洗后板片安装顺序  下一篇:板式换热器的应用场合
公司动态|友情链接|会员中心|站内搜索|网站地图

联系人:董经理 手 机:13276433666

邮 箱:1223686993@qq.com

Powered by MetInfo 5.3 ©2008-2020  MetInfo Inc.

友链:反应釜 清洗机 螺旋板换热器 反应釜 燃气锅炉陶瓷喷涂 钢格板 反应釜硫化机 热风炉 螺旋输送机 反应釜净化车间 远东电缆 真空干燥机 转轮除湿机 吊篮租赁 焚烧炉 高压清洗泵 刮板式薄膜蒸发器 高压水清洗机 气浮机闭式冷却塔 液压油管 静电消除器 真空耙式干燥机 智能电表